Download complete project materials on Predicting And Calculating The Laminar Flow Of Fluid In Pipe Using Ansys Fluent Software from chapter one to five
ABSTRACT
PASS 2024 UTME WITHOUT STRESS:- 👉 DOWNLOAD and PRACTICE with 2023 UTME CBT APP 📱👈
CLICK to DOWNLOAD NOW.:- 👉 PASS Your POST UTME by Downloading Your School's Post UTME Past Questions and Answers 📱👈
The project aimed at predicting and calculating the laminar flow of fluid in pipe using ANSYS fluent software. The ANSYS FLUENT software used finite volume method to stimulate the flow of fluid in a given pipe.
The problem given in this project is to stimulate and consider the fluid flowing through a circular pipe at a constant radius .And the parameter given for the pipe are as follow : L=8m,D=0.2,µ=2×10-3kg/Ms. The inlet velocity is to be constant over the cross section. The expected resultof the problem are velocity vector, velocity magnitude condition, pressure contour , velocity profile at the outlet and skin friction coefficient along the pipe wall.
The ANSYS fluent software is used to solve the problem given and the steps involve are, Building of Geometry, Creation of mesh, coefficient and Results.
The Geometry stage is where the parameter Land D given is inserted by drawing a rectangle on the XY-plane. Which V1=0.2m for the diameter and H2=8m for the length.
Under the creation of mesh the pipe wall is divided into 100 elements in the axial direction and 5 elements in the radial direction. This is done in order to predict and visualize the condition and fluid flow on each region of the pipe.
Each edge of the pipe named in order to assign boundary condition in FLUENT in later steps. Therefore the left side of the pipe named Inlet, The right side named outlet, the top side named pipe wall and the bottom side named centerline.
In conclusion, the flow of fluid for the velocity vector moved uniformly within the inlet region and gradually the flow of fluid developed continuously until it is full developed within the outlet.
CHAPTER ONE
1.0 INTRODUCTION:
Chapter two literature review explain the various past projects that have been done about stimulation and calculation involving laminar flow in a pipe using CFDANSYS FLUENT software package.
Chapter three give details on calculation modeling where Reynolds experiment and procedure followed have been analyzed.
Chapter four gives the details about the building of Geometry, Launching of design modeler, start creation sketch on XY plane with how to Dimensioning the rectangle. More so, the project discussed the Creation of Mesh where the pipe is divided into 100 elements in the axial direction and 5 elements in the radial direction with Edge sizing the specifying the number of division.
Chapter five explained the procedure of how to set the Boundary condition with the velocity inlet and centerline boundary condition and pipe wall boundary condition.
Chapter six shows the Result presentation of velocity vector at the outlet of the pipe with velocity magnitude contours which give the rough surface at first instance but by increasing the number of contour the result gives smooth surface at the inlet, are able to show the pressure contours which is plotted on a chart so location was created along the XY axis of the pipe outlet, where we further calculate for skin friction coefficient.
Chapter seven discussed the conclusion and recommendations made based on this project
PROJECT OUTLINE
Problem specification
Pre-Analysis and start up
Building of geometry
Creation of mesh
Physics set up of pipe flow
Numerical solution
Numerical result using CFD prost post
Verification and validation
1.3 Aim and Objectives of the Project are as follows:
1.3.0 Aim
To provide student with an understanding of the principle of fluid mechanics and the numerical procedure in CFD.
1.3.1 Objectives
To understand the fundamental of viscous incompressible flows, the fundamental of compressible flow and learn the basic of non-viscous potential flows.
To be able to understand fluid dynamics principle and their application -.To be able to demonstrate competence in setting up computational fluid dynamic models, meshing, parameterization and post processing for some industrial important application. The technical competence in building and conducting CFD simulation is a skill which enhances employability.
To be formulate and solve incompressible laminar flow in a Cartesian and polar coordinates.
To be familiar with computational fluid dynamic with also demonstrate the use of ANSYS FLUENT code for solving two-dimensional laminar and turbulent flow
To be familiar with stream function and potential function and elementary potential flows.
CLICK HERE TO DOWNLOAD THE COMPLETE MATERIAL (CHAPTER 1 -5)
>GUARANTTEE|:| Score 280 Above in 2024 UTME👉 DOWNLOAD FREE JAMB CBT APP HERE:.: GURRANTTEE Score 280 Above in 2022 UTME👉 DOWNLOAD FREE JAMB CBT APP HERE 📱👈WISH TO STUDY & LIVE in UK?:- STUDY, WORK AND LIVE IN the UK Application Form NOW OUT. Call 08030447894
